ELECTRONIC ACCESSORIES

This 30cm servo extension cable has three 22-AWG wires joining a male Futaba J connector and a female JR connector. Since a female JR connector can be plugged into a male Futaba J connector, each end of the cable is compatible with both Futaba and JR-style connections; this cable will work as an extension cable in either system or as an adapter between systems, and it is compatible with almost all of the servos in the Kitronik range

The connectors have contacts on a 0.1" spacing, and each wire is comprised of 60 strands, making this cable more flexible than standard servo cables.

Features:

Compatible with all standard servo types including a Mini 180 degree servo.

Also compatible with a Mini 360 degree continous rotation servo.

Servo cable colour convention:

Brown or black = ground (GND, battery negative terminal).

Red = servo power (Vservo, battery positive terminal).

Orange, yellow, white, or blue = servo control signal line

This 60cm servo extension cable has three 22-AWG wires joining a male Futaba J connector and a female JR connector. Since a female JR connector can be plugged into a male Futaba J connector, each end of the cable is compatible with both Futaba and JR-style connections; this cable will work as an extension cable in either system or as an adapter between systems, and it is compatible with almost all of the servos in the Kitronik range.

The connectors have gold-flashed contacts on a 0.1" spacing, and each wire is comprised of 60 strands, making this cable more flexible than standard servo cables.

Features:

Compatible with all standard servo types including a Mini 180 degree servo.

Also compatible with a Mini 360 degree continuous rotation servo.

Servo cable colour convention:

Brown or black = ground (GND, battery negative terminal).

Red = servo power (Vservo, battery positive terminal).

Orange, yellow, white, or blue = servo control signal line.

This is a 4 pack of wires that are pre-terminated with an alligator (crocodile) clip on one end and a hookup pigtail (male jumper connector) on the other. Alligator clips are a staple part for any workbench and with these cables you will be able to easily incorporate those clips into a breadboard, development platform, or anything else that you would normally be able to attach a male jumper connector to.

Each Alligator Clip with Pigtail cable has a wire length of 30cm (that’s a little less than 1ft) and a male pin that easily inserts into a standard 0.1" connector. Each pack consists of two red cables and two black cables.

These connector wires can also be used to connect a BBC microbit to a prototyping board as an alternative to an edge connector.

Features:

Wires with a croc clip on one end and a male jumper cable connector (pigtail) on the other.

Enables you to connect a BBC microbit to a prototyping board as an alternative to using an edge connector.

Contents:

2 x Red alligator to male jumper connector leads.

2 x Black alligator to male jumper connector leads.

Dimensions:

Length: 30cm.

The Plastic Desoldering Pump with PTFE Nozzle features a durable blue plastic body designed for efficient and reliable solder removal. The PTFE (polytetrafluoroethylene) nozzle provides excellent heat resistance and smooth operation, making it ideal for precision desoldering tasks.

The pump is easy to use, with a comfortable grip and a powerful suction mechanism to effectively remove molten solder from circuit boards and electronic components. This essential tool is perfect for hobbyists, technicians, and professionals who require a dependable solution for desoldering needs.

Ideal for technicians, a comprehensive electronics toolkit supplied within a handy zipped tool bag - external dimensions: 340 x 210 x 50mm.

Kit Contents:

20W/130W Soldering iron

Desoldering pump

Multimeter

5" Long nose pliers

5" Side cutters

Slotted precision screwdriver: 2.5 x 75mm

Phillips precision screwdriver: PH00 x 75mm

Slotted screwdrivers: 4 x 75, 5 x 75, 6 x 125mm

Phillips screwdrivers: PH0 x 75, PH1 x 75, PH2 x 125mm

Mains tester screwdriver

Wire stripper/cutter

8pc Hex key set: 1.5, 2, 2.5, 3, 4, 5, 5.5, 6mm

IC extractor

Tweezers

Great value starter soldering iron kit. Everything you need to start soldering in one handy pack, including a 30W mains powered soldering iron.

Contents:

1 x 30W Soldering iron.

1 x Safety stand.

1 x Desoldering pump.

Lead free solder.

Watch this video below for an explanation of some of the components in the kit (please note: not all items in the video are included in this kit, see contents list for exact contents).

Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have.

Each lead in this pack of ten is 35cm long with a rubber shrouded alligator clip in 45mm length and 8.3mm opening on each end. There are three different colours, you get each of: red, black and yellow.

This is a micro servo It only weights 20g and provides a 1.6kg.com torque. It will comes with a 3-pin control cable and mounting hardware.

Almost all the micro bit servo in the market have to be driven by 5V, but the normal working voltage for micro:bit is 3V. It is embarrassing to drive a 5V servo with a micro:bit. Thus, we have customized these two servos that can be driven by two batteries with the lowest working voltage at 2.7V. It is the first batch of the micro bit servo designed for the micro:bit in the market.

The high linearity makes its control more accurate. It is designed for micro:bit with high-linearity, which gives you a smooth feel of control.

Low working voltage, compatible to 3V-5.5V(With 2.7V at least), designed for micro:bit.

ELECFREAKS micro:servo is a kind of 360 deg analog servo. It is light and portable, a little bigger than 5 cent coin. It works at 3V voltage and uses pulse width to adjust speed of the servo rotation, which also can be used to make small robot modules, mechanical arm modules and intelligent car modules.

Introduce students to hands-on electronics and lighting with this engaging USB lamp kit, ideal for classroom or individual projects. The Flexible LED Noodle Filaments USB Lamp Kit (5 Pack) allows learners to build their own colourful LED lamp signs while developing essential skills in soldering and assembly.

Each kit includes everything needed to create five USB-powered lamp projects, each using a different flexible filament colour. Designed for Key Stage 3 and Key Stage 4 (ages 11+ and 14+), this kit provides an excellent starting point for exploring the basics of electronics, lighting, and practical design.

Kit Contents:

5 x Flexible LED noodle filaments (1 of each colour)

5 x USB power leads

5 x Resistors

5 x Switches

1m Red wire

1m Black wire

Notes:

Soldering is required

Mechanical assembly is required

Add passive infrared detection (PIR) to your project with this PIR Motion sensor large lens version. Its 2.54mm pitch connector pins makes the job of connecting it to your project an easy one.

It features a large lens which allows for a long range and a wide viewing angle. Typical values for detection are; up to 9m detection range and a viewing angle of up to 120°.

The operating voltage is between 3V - 5.5V with a max current of 100uA. So, it's operating requirements won't be much of a drain on power, which is good news if your power is being supplied by batteries.

Features:

It has a long detection range, up to 9m.

It features a wide viewing angle, up to 120°.

Very low power consumption.

Dimensions:

Length: 36mm.

Width: 26mm.

Height: 21mm.

Pin Pitch: 2.54mm

High torque 5 pole DC motor with wide operating range 12-24V. Suitable for water pumps, robotics etc. Rotation is counter-clockwise as viewed from shaft end.

Dimensions: L: 32.5 (exc. shaft) x 27.5mm dia.

Shaft: 12.8mm long x 2.3 dia.

Weight 52g approx.

Mounting holes 2 x M2.6 x 0.45 tapped.

RoHS compliant

Operating range: 12-24V (nominal 18V)

No load speed: 18000 RPM ±10%

No load current: 0.32A

Load speed: 14350 RPM ±8%

Current at max. efficiency: 1.3A

Rated load (with fan) 65g-cm

Output: 0.42W

Torque: 11.6g-cm

Stall torque: 55g-cm min.

Stall current: 1.4A max.

2 x AA Battery Cage with leads, with 150mm colour coded flying leads. This battery cage houses two AA batteries and is barely bigger than the batteries it is designed to hold. This makes it a suitable choice for the smaller projects when a discrete and easy to hide battery cage is what is called for.

It also features colour coded 150mm flying leads, making for easy integration into your projects.The battery cage can easily be soldered directly to a board or connected to your project via terminal blocks.

Features:

Small discreet size.

150mm colour coded flying leads.

The leads are suitable for soldered connections.

The leads are suitable for terminal block connections.

Contains:

1 x 2 AA Battery Cage with 150mm colour coded flying leads.

Dimensions:

Leads: 150mm

This 3V vertical submersible low power water pump is an ideal solution for creating a small indoor water feature or as part of a plant watering system. At the heart of the pump is a 3V DC motor that runs quietly and only draws approximately 100mA.

The pump needs priming before use and should be kept fully submerged during use as it will only pump water not air. Also, it only works in one direction as a pump, you cannot reverse the connections and have it move water in the other direction.

It's 3V, 100mA power requirements are such that you could use a microcontroller with suitable drive capacity to switch it on or off. As the new micro:bit now has 200mA available for powering external devices, this pump can be powered directly by the micro:bit V2.

The micro:bit can only drive 15mA from its pins, so a transistor or FET is required to control it from the pins, either in an on/off capacity, or, with PWM to vary pumping rate. If using the original micro:bit or if the microbit is already controlling other devices, this pump can also be powered and controlled via a motor driver board, or similar.

Note: This pump is not supplied with any tubing.

Features:

Vertical type submersible pump.

Operating power requirements are; 3V and 100mA.

Low noise DC motor.

Can be controlled with a simple on/off switch or microcontroller/motor driver board.

Ideal for small water features or plant watering systems.

A flow rate of 80L/H @ 3V and 100L/H at 4.5V.

Contents:

1 x 3V Vertical Submersible Water Pump.

Dimensions:

Length: 38.5mm.

Width: 23.9mm.

Height: 42.6mm.

3xAA Covered Battery Holder with built-in on/off power switch and Leads. Supplied with 150mm colour coded flying leads. Features a sliding cover for easy access to battery compartment. Case is hard plastic and is resistant to sudden impacts and vibrations. Ideal in any project kit requiring AA battery power.

Features:

On/off power switch.

Holds 3 x AA batteries.

Sliding case for easy access.

150mm colour coded flying leads

Case resistant to sudden impacts and vibrations.

Contents:

1 x 3xAA Covered Battery Holder with Switch and Leads.

Dimensions:

Length: 69mm.

Width: 48mm.

Height: 20mm.

Compatible with:

Raspberry Pi Pico

Micro:Bit

This battery cage houses four AA batteries and features a PP3 clip connection. This allows for quick and easy removal from a project.

The batteries are arranged in a 2 over two configuration to allow for a relatively small footprint, which will make it easier to accommodate inside enclosures where space is at a premium as the cage is a little more than 1 AA battery in length.

Features:

Houses 4 x AA batteries.

Features a PP3 clip connector.

Arranged in a 2 over two configuration for a smaller footprint.

4xAA Covered Battery Holder with built-in on/off power switch and leads. Supplied with 150mm colour coded flying leads. Features a sliding cover for easy access to battery compartment. Case is hard plastic and is resistant to sudden impacts and vibrations. Ideal in any project kit requiring AA battery power.

Note: this product does not have the JST connector to connect to the micro:bit

Features:

On/off power switch.

Holds 4 x AA batteries.

Sliding case for easy access.

150mm colour coded flying leads

Case resistant to sudden impacts and vibrations.

Contents:

1 x 4xAA Covered Battery Holder with Switch and Leads.

Dimensions:

Length: 68mm.

Width: 65mm.

Height: 19mm.

Compatible with:

Raspberry Pi Pico

Micro:Bit

This 2xAAA Battery Cage with JST connector is compatible with the Igloo, PICAXE wearable module and the BBC micro:bit. Supplied with 145mm colour coded power leads and a JST connector at the end, this battery cage is light and features a M3 mounting hole in the centre so it can be attached to the back of BBC micro:bit cases. The JST connector easily plugs into the Igloo and BBC micro:bit to provide a portable power supply. Ideal in any project kit with a JST connector power supply interface.

Features:

JST connector for easy power supply connections.

Holds 2 x AAA batteries.

Clips hold AAA batteries securely in place.

145mm colour coded power leads and a JST connector.

Clip holder resistant to sudden impacts and vibrations.

Contents:

1 x 2 x AAA Battery Cage with JST Connector.

Dimensions:

Length: 53mm.

Width: 25mm.

Height: 13mm.

This 3 x AAA battery holder with power leads that terminate in a JST connector. The leads are colour coded and 150mm long. The holder also features two mounting holes so that the battery holder can be permanently mounted on a project or surface.

This battery holder is ideal for any project that requires 4.5V of battery power delivered via a JST connection.

Features:

Holds 3 x AAA Batteries.

Mounting holes allowing for permanent attachments to projects or surfaces.

150mm colour coded leads with a JST connector.

Contents:

1 x (3xAAA) Battery holder with JST connector.

Dimensions:

Length: 52.5mm.

Width: 37.5mm.

Height: 12mm.