MICRO BIT & KITS

These are 20cm long jumpers with female connectors on both ends. Use these to jumper from any male header on any board to any other female header. Multiple jumpers can be installed next to one another on a 0.1" (2.54mm) header.

Features:

Female to Female connectors.

20cm Long.

For use with breakout boards with a standard 0.1" (2.54mm) pin spacing.

1 x 40 pack F/F Jumpers (four of each colour).

This is a standard duty PP3 clip lead with a soft case, similar to connectors found in many standard consumer electronics products.

It also features pre-tinned colour coded 150mm flying leads, making for easy integration into your projects.

This clip lead can easily be soldered directly to a board or connected to your project via terminal blocks.

Features:

Standard duty construction.

150mm colour coded pre-tinned flying leads.

It features a standard PP3 connector.

The leads are suitable for soldered connections.

The leads are suitable for terminal block connections.

Contains:

1 x Standard duty PP3 battery clip with 150mm colour coded flying leads.

Dimensions:

Leads: 150mm

ElecFreaks Smart Cutebot Pro Robot Car Kit is a programming robot for STEAM education, it equips with a 4-way infrared line-following sensor, an encoder motor, the LED rainbow light, an ultrasonic sensor, and other devices. With the encoder motors, the Cutebot Pro provides the flexibility to control the distance the cart travels and enables more precise control of the turning angle. The Cutebot Pro also offers a variety of expansion interfaces to allow for the expansion of additional hardware to stimulate imagination and creativity.

Closed-loop motor for more precise driving, Compared with Cutebot, our cutebot pro has an upgraded motor. From the open-loop motor to the closed-loop motor, the ElecFreaks Smart Cutebot Pro Robot Car can receive instructions more accurately and the driving route can be more accurate.

4 line-tracking sensors to identify more complex lines, ElecFreaks smart Cutebot Pro is upgraded to 4 line-tracking sensors, which can identify more complex intersections such as crossroads or T-junctions. 4 line-tracking sensor data can be fused into one line of analog data to realize PID line inspection. At the same time, it can also combine many sensors and building blocks to realize more application scenarios.

Lithium battery power supply, The newly upgraded Cutebot Pro no longer needs to buy a lithium battery expansion pack. It carries a lithium battery box and supports 2000ma lithium battery power supply, which makes the battery life longer and can create more cases. Batteries required are 3.7V 18650 Lithium-Ion Rechargeable Battery 2.6Ah

More sensors and structural parts can be expanded, ElecFreaks Smart Cutebot Pro Robot Car adds an additional motor expansion interface, adding more holes for structural parts, which can expand structural devices such as mechanical arms, and can create more fighting cases.

More sensors and structural parts can be expanded, The Smart Cutebot Pro Robot Car adds an additional motor expansion interface, adding more holes for structural parts, which can expand structural devices such as mechanical arms, and can create more fighting cases.

ELECFREAKS XGO Robot Kit V2 for micro:bit is a bionic quadruped robot dog kit specially designed for artificial intelligence education for teenagers. It can be combined with the micro:bit to perform graphical programming on MakeCode, which is more suitable for teenagers to learn to program.

ELECFREAKS XGO Robot Kit V2 for micro:bit is a bionic quadruped robot dog kit specially designed for artificial intelligence education for teenagers. It can be combined with the micro:bit to perform graphical programming on MakeCode, which is more suitable for teenagers to learn to program. With 15 DOF, it can perform and interact like a real pet dog, as well as pinch and carry with its robotic arm, allowing children to learn mechanics, electronics, programming, and AI as they play with it, and getting them prepared for the future life of AI.

Compared with the XGO V1, the XGO Robot Doc Kit V2 has three more high-quality digital servos, which can support more vivid and dynamic movements.

The XGO Robot Dog Kit V2 is equipped with a 6-axis IMU, joint position sensors, and current sensors to provide its own attitude feedback, which can be used for algorithm verification and secondary development. At the same time, it also has a speaker sensor, which makes the product more vivid.

Programme the joystik:bit to control XGO V2 through the makecode platform

Use the self-developed APP to control XGO V2

XGO Robot Dog Kit V2 is equipped with a 3-axis arm, which can realize intelligent gripping, pushing and handling

If you have a standard servo and need to connect it to a board that accepts crocodile clip connections then our new servo to crocodile clip adapter cable is the accessory for you.

The adapter cable features 100mm colour coded cables terminating in a male servo connector at one end and colour coded 35mm croc clip at the other. The servo to crocodile clip adapter cable is ideal for connecting standard servos to the Kitronik Klip Motor Driver Board for microbit.

Features:

This adapter cable allows you to attach a standard servo to a board that accepts crocodile connections.

Colour coded 100mm leads and crocodile connector covers.

Ideal for use in robotics/Buggy projects.

Dimensions:

Length: 135mm.

The colour changing LED on this kit turns on when it goes dark and stays on for a period of time. This makes a good night light and because the LED is only on for a small amount of time the batteries last much longer than a light that is on all night.

There is an on board trimmer to set the light level at which the LED turns on and another trimmer to set how long the LED stays on for. The maximum duration is about 30 minutes. When set to 15 minutes and activated once a night the batteries will last two months.

Features:

Adjustable light level sensor.

Adjustable length of light time.

Contents:

2 x 10K Resistor.

2 x 1M Resistor.

1 x PCB trimmer 220K POT.

1 x PCB trimmer 10M POT.

1 x 47R Resistor.

1 x Miniature LDR.

1 x Capacitor, Electrolytic, 16V, 470uF.

4 x 2N7000 N Chanel FET.

1 x Colour Changing 5mm Diffused LED - 750mCd.

1 x PP3 Battery Clip Lead (Heavy Duty).

1 x 3xAA Battery Cage with Clip.

1 x Timed Night Light Kit PCB.

Dimensions:

PCB Length: 53mm.

PCB Width: 41mm.

Requires:

3 x AA Batteries.

Soldering Iron.

Solder.

Wire Cutters.

The :MOVE mat line following and activity maps - A1 size is an accessory for :MOVE Motor, :MOVE mini and also the Edison V2 Robot. It can be used just for fun, or as part of a project in the classroom. The mat is double-sided, with a line following track on one side and a mock-up of a town on the other.

The line following side offers an attractive alternative to having to create a track by hand. No more fighting with a roll of tape and no more cleaning up adhesive residue afterwards. Level up your line following game today!

The town mock-up side provides a great place to set up traffic projects, where other props can be used. Things such as LAMP:bit, STOP:bit, and also ACCESS:bit can be utilised to great effect.

The mat is A1 in size, which is a generous 594mm x 841mm. When not in use it can either be stored flat or folded up.

Features:

A double-sided accessory mat for :MOVE Motor for micro:bit and Edison V2 robot.

Great for use at home and in the classroom.

On one side there is a line following track and on the other a town mock-up.

No more creating line following tracks with tape and no more clean-up afterwards.

Create town projects, utilising Kitronik traffic calming type props.

When not in use it can be stored flat.

Contents:

1 x :MOVE mat line following and activity maps - A1 size.

Dimensions:

Length: 841mm.

Width: 594mm.

Requires:
A suitable buggy, preferably with line following capabilities. Such as;

Kitronik :MOVE Motor for micro:bit

Edison V2.0 Robot

 

Makey Makey GO empowers modern-day creators, visionaries, and innovators with the freedom to invent wherever inspiration strikes. With Makey Makey GO, innovation is at your fingertips - literally. Simply attach an alligator clip, and watch ordinary objects transform into Internet touchpads, ready to revolutionize the world.

Compact enough to hang on your keychain or slip into your pocket, Makey Makey GO is poised to ignite even more STEM projects than its predecessor, the acclaimed Makey Makey, which earned a spot on Consumer Reports' list of "Best Tech Toys of 2014.

Turn everyday objects like bananas into touchpads!

Connect the world around you to your computer! Setup takes just seconds.

Just plug, clip, and play! No programing knowledge needed. No software to install. Works with Mac and Windows.

1000s of possibilities! Make Cardboard Smart Swords, Slack Line Score Boards, and Animal Skype Phones.

Ages 8 to infinity.

Contents:

1 USB Invention Stick

Case with magnet

1 white alligator clip (2.5 ft)

Keyring

Instruction guide