All Categories
    Menu Close

    MonkMakes Servo Kit for Micro:bit

    Manufacturer: Monk Makes
    The Servo Kit for micro:bit makes it easy to connect up three servomotors from your micro:bit. The kit is supplied with the servo board, three servos, a battery cage, and alligator/crocodile leads. The MonkMakes Servo for microbit board provides a really easy way to attach up to three servomotors to a BBC micro:bit. The board requires a power supply or battery pack to provide 5 or 6V to the servomotors. It includes a voltage regulator that will supply 3V back to the micro:bit, so that you don’t have to power it separately.

    The board has been designed to allow for alligator/crocodile connections to the microbit. This means that there is no need for mechanical assembly or soldering. You can write code for the attached microbit using either the MakeCode editor or MicroPython.

  • Allows you to control the 3 servos provided with the microbit.
  • When powered the board will supply power to the servos and microbit.
  • Connect it to the microbit with alligator/crocodile clips.
  • Use the MakeCode blocks/javascript or MicroPython editors.

  • Contents:
  • 1 x Monk Makes servo board for the microbit.
  • 3 x 9g servomotors and arm kits.
  • 1 x 4xAA battery box.
  • SKU: MONK 075
    Availability: 6 in stock
    i h
    Ship to
    Shipping Method
    Estimated Delivery
    No shipping options

    Product Resources / Datasheet

    Products specifications
    Device TypeKits
    Customers who bought this item also bought
    Picture of Kitronik Flat Profile Tact Switch Buzzer

    Kitronik Flat Profile Tact Switch Buzzer

    KI 3420
  • A low profile Miniature PCB Mount TACT Switch.
  • Single pole normally open contact.
  • Max voltage = 24V DC.
  • Max current = 50mA. L 6, W 6, H 4.3 mm.
  • L 6, W 6, H 4.3 mm.
  • This part is found in the Kitronik Inventors Kit
  • €0.50
    Picture of Grove Ultrasonic Distance Sensor

    Grove Ultrasonic Distance Sensor

    KI 46153
    The Grove Ultrasonic Distance Sensor is an ultrasonic transducer that utilizes ultrasonic waves to measures distance. It can measure from 3cm to 350cm with the accuracy up to 2mm. It is a perfect ultrasonic module for distance measurement, proximity sensors, and ultrasonic detector.

    This module has an ultrasonic transmitter and an ultrasonic receiver so you can consider it as an ultrasonic transceiver. Similar to sonar, when the 40KHz ultrasonic wave generated by the transmitter encounters the object, the sound wave will be reflected back, and the receiver can receive the reflected ultrasonic wave. It calculates the time from the transmission to the reception, and then multiplies it by the speed of the sound in the air(340 m/s) to calculate the distance from the sensor to the object.

    Compared with traditional ultrasonic module, the HC-SR04, the Grove Ultrasonic Distance Sensor integrates a single-chip microcomputer, and the transmitting signal and the receiving signal share one pin by time division multiplexing, so only one I/O pin is occupied. Another difference is that HC-SR04 only supports 5v voltage, while Grove - Ultrasonic Distance Sensor supports 5v and 3.3v. As we know, the Raspberry pi I/O only supports 3.3v. Therefore, Grove - Ultrasonic Distance Sensor can be directly connected to the I/O of the Raspberry Pi, but HC-SR04 needs to use a voltage conversion circuit.

  • 3.3V/5V compatible, wide voltage level: 3.2V ∼ 5.2V.
  • Only 3 pins needed, save I/O resources.
  • Wide measurement range of 3cm ∼ 350cm.
  • Easy to use, grove connector, plug and play.

  • Possible Applications:
  • Distance measurement.
  • Ultrasonic detector.
  • Proximity alarm.
  • Smart car/buggy/robot.

  • Dimensions:
  • Length: 50mm.
  • Width: 25mm.
  • Height: 16mm.
  • €10.95
    Picture of Kitronik PIR Motion Sensor

    Kitronik PIR Motion Sensor

    KI 4633
    This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the ‘alarm’ pin will go low.

    This unit works great from 5 to 12V (datasheet shows 12V).

    The alarm pin is an open collector meaning you will need a pull up resistor on the alarm pin. The open drain setup allows multiple motion sensors to be connected on a single input pin. If any of the motion sensors go off, the input pin will be pulled low.

    Gone is the old “odd” connector, now you will find a common 3-pin JST! This makes the PIR Sensor much more accessible for whatever your project may need. Red = Power, White = Ground, and Black = Alarm.
    Picture of Mini Glue Gun Low Temp

    Mini Glue Gun Low Temp

    CR 391165
  • Mini glue gun
  • Melts glue at 130°C (low temperature)
  • Includes 2 sticks of 10cm and adaptor
  • Lead should not rolled tightly, as the insulated conductors can be damage
  • €7.24