Cookies help us deliver our services. By using our services, you agree to our use of cookies.
Search
From the same category
40-pin GPIO Ribbon Cable for Raspberry Pi
PIM CAB0505
This 175mm long GPIO (general purpose input/output) ribbon cable lets you extend the reach of your Raspberry Pi's pins, bridging them out to other boards or PCBs. The Raspberry Pi's GPIO can be used for all sorts: twiddling pins on or off, providing 3.3V or 5V power, communicating with I2C or SPI devices, and much more. This cable gives you a bit more flexibility in where you route those signals.
175mm long x 51mm wide 40 wires, 2x20 pin female connectors Pin 1 is marked by the white/pink wire
Note: Be careful to connect this cable to your board the correct way around. You can't use it with a male header to connect to a HAT's female header, as the pins will be mirrored. You'll risk damaging both your board and your Raspberry Pi if you connect the cable incorrectly so, if in doubt, check the order of the pins on the connector with a multimeter before connecting things up!
Compatible with:Raspberry Pi 4 Raspberry Pi 5
Note: Be careful to connect this cable to your board the correct way around. You can't use it with a male header to connect to a HAT's female header, as the pins will be mirrored. You'll risk damaging both your board and your Raspberry Pi if you connect the cable incorrectly so, if in doubt, check the order of the pins on the connector with a multimeter before connecting things up!
Compatible with:
€5.50
Flexible Tripod for Raspberry Pi High Quality Camera
PIM COM-B017
Light, flexible, and stable, the perfect partner for the Raspberry Pi High Quality Camera
The three flexible legs will hold your camera stable on your desk, or can be wrapped around a support for more unusual placements. The head is also on a ball joint, so the camera can be angled to get the perfect shot! Fitted with a standard 1/4"-20 camera mount the tripod will mate securely with the Raspberry Pi High Quality Camera, but can also be used with a wide variety of other products including GoPro. The rubber feet will keep your camera from sliding and the lightweight and compact construction makes this usefully portable.
Colour may differ from picture.
Compatible with:Raspberry Pi High Quality Camera
The three flexible legs will hold your camera stable on your desk, or can be wrapped around a support for more unusual placements. The head is also on a ball joint, so the camera can be angled to get the perfect shot! Fitted with a standard 1/4"-20 camera mount the tripod will mate securely with the Raspberry Pi High Quality Camera, but can also be used with a wide variety of other products including GoPro. The rubber feet will keep your camera from sliding and the lightweight and compact construction makes this usefully portable.
Colour may differ from picture.
Compatible with:
€5.55
Pimoroni Display HAT Mini for Raspberry Pi
PIM 589
A generous 2.0" (320 x 240) IPS LCD display for Raspberry Pi with lots of tasty baked in functionality.
Display HAT Mini features a bright 18-bit capable 320x240 pixel display with vibrant colours and formidable IPS viewing angles, connected via SPI. It's got four tactile buttons for interacting with your Pi with your digits and a RGB LED for notifications. Pimoroni have also squeezed in a QwST connector (Qwiic / STEMMA QT) and a Breakout Garden header so it's a doddle to connect up different kinds of breakouts.
It will work with any model of Pi with a 40 pin header, it goes with the Raspberry Pi Zero particularly well - Pimoroni have included a pair of standoffs so you can use to bolt HAT and Pi together to make a sturdy little unit. To accommodate the screen Display HAT Mini is a bit bigger than a standard mini HAT or pHAT - it's around 5mm taller than a Pi Zero (so a Mini HAT XL or a Mini HAT Pro, if you will).
Display HAT Mini lets you turn a Raspberry Pi into a convenient IoT control panel, a tiny photo frame, digital art display or gif-box, or a desktop display for news headlines, tweets, or other info from online APIs. This screen is a handy 3:2 ratio, useful for retro gaming purposes!
Features:2.0” 320x240 pixel IPS LCD screen, connected via SPI (~220 PPI, 65K colours) 4 x tactile buttons RGB LED Qw/ST (Qwiic/STEMMA QT) connector Breakout Garden / I2C header Pre-soldered socket header for attaching to Raspberry Pi Compatible with all models of Raspberry Pi with a 40 pin header. Fully assembled No soldering required (as long as your Pi has header pins attached). Dimensions: approx 65.5mm x 35mm x 9mm (W x H x D, includes header and display). With a Pi Zero attached with standoffs, the total depth is 17mm. Screen usable area: 40.8mm x 30.6mm (L x W) Pinout Schematic Dimensional drawing Display HAT Mini Python library ST7789 Python library
IncludesDisplay HAT Mini 2 x 10mm standoffs
Compatible with:Raspberry Pi 5 Raspberry Pi 4 Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Header for Pi Zero)
Display HAT Mini features a bright 18-bit capable 320x240 pixel display with vibrant colours and formidable IPS viewing angles, connected via SPI. It's got four tactile buttons for interacting with your Pi with your digits and a RGB LED for notifications. Pimoroni have also squeezed in a QwST connector (Qwiic / STEMMA QT) and a Breakout Garden header so it's a doddle to connect up different kinds of breakouts.
It will work with any model of Pi with a 40 pin header, it goes with the Raspberry Pi Zero particularly well - Pimoroni have included a pair of standoffs so you can use to bolt HAT and Pi together to make a sturdy little unit. To accommodate the screen Display HAT Mini is a bit bigger than a standard mini HAT or pHAT - it's around 5mm taller than a Pi Zero (so a Mini HAT XL or a Mini HAT Pro, if you will).
Display HAT Mini lets you turn a Raspberry Pi into a convenient IoT control panel, a tiny photo frame, digital art display or gif-box, or a desktop display for news headlines, tweets, or other info from online APIs. This screen is a handy 3:2 ratio, useful for retro gaming purposes!
Features:
Includes
Compatible with:
€26.95
Pimoroni Enviro for Raspberry Pi
PIM 486
Keep track of your surroundings using Enviro for Raspberry Pi! Equipped with a variety of advanced environmental sensors, these boards feature a beautiful full-color LCD screen to showcase your data. They offer an ideal introduction to citizen science and environmental monitoring!
Enviro is designed for indoor monitoring, letting you measure temperature, pressure, humidity, light, and noise level. It's great for keeping tabs on what's going on in rooms in your house, office, or elsewhere. Push the data to server and you can view the data remotely from anywhere.
BME280 temperature, pressure, humidity sensor (datasheet) LTR-559 light and proximity sensor (datasheet) MEMS microphone (datasheet) 0.96" colour LCD (160x80) Pimoroni breakout-compatible pin header pHAT-format board Fully-assembled Compatible with all 40-pin header Raspberry Pi models Python library Dimensions: 65x30x8.5mm
Compatible with:Raspberry Pi 5 Raspberry Pi 4 Raspberry Pi Zero (but needs Male 40-pin 2x20 HAT Header for Pi Zero)
Enviro is designed for indoor monitoring, letting you measure temperature, pressure, humidity, light, and noise level. It's great for keeping tabs on what's going on in rooms in your house, office, or elsewhere. Push the data to server and you can view the data remotely from anywhere.
Compatible with:
€39.95
Pimoroni Explorers Hat Pro for Raspberry Pi
PIM 082
Unlock a world of possibilities with the Raspberry Pi Pimoroni Explorer's Hat Pro for 40 Pin. Seamlessly integrate sensors, buttons, and LEDs into your Raspberry Pi projects, transforming them into interactive experiences. Whether you're building robots, IoT devices, or custom interfaces, this Hat delivers unparalleled control and functionality. Its compact form factor and easy-to-use design make it the ideal choice for makers of all skill levels. Elevate your Raspberry Pi projects with the Pimoroni Explorer's Hat Pro and explore the endless potential of your creations.
Four buffered 5V tolerant inputs (perfect for Arduino compatibility) Four powered 5V outputs (up to 500mA total across all four channels) Four capacitive touch pads (labelled 1, 2, 3, 4) Four capacitive crocodile clip pads (labelled 5, 6, 7, 8) Four coloured LEDs (red, green, blue, and yellow) Four analog inputs Two H-bridge motor drivers (up to 200mA per channel; soft PWM control) A heap of useful (unprotected) 3v3 goodies from the GPIO A mini breadboard on top! Explorer HAT Pro pinout Compatible with all 40-pin header Raspberry Pi models/li> Python library Comes fully assembled
Notes
The inputs use a 5-channel buffer that will accept anything from 2V-5V as logic high
Mini breadboard had 170 points, 17x5 per half of the breadboard
Compatible with:Raspberry Pi 4 Raspberry Pi 5 Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Header for Pi Zero)
Notes
The inputs use a 5-channel buffer that will accept anything from 2V-5V as logic high
Mini breadboard had 170 points, 17x5 per half of the breadboard
Compatible with:
€27.95
Pimoroni GFX HAT - 128x64 LCD Display for Raspberry Pi
PIM 400
A 128x64 pixel, 2.15" LCD display with snazzy six-zone RGB backlight and six capacitive touch buttons. GFX HAT makes an ideal display and interface for your headless Pi projects.
GFX HAT riffs off the previous Display-O-Tron HAT (now discontinued), but gives you the flexibility of individual pixels, letting you display more complex graphics and real typefaces, while retaining the handy capacitive touch buttons for input/navigation.
Features:128x64 pixel, 2.15" LCD display Integrated diffuser/reflector assembly Six-zone RGB LED backlight SN3218 LED driver chip (I2C address 0x54) Six capacitive touch buttons with white LEDs Microchip CAP1166 capacitive touch/LED driver chip ((I2C address 0x2c) Compatible with all 40-pin header Raspberry Pi models Python library Comes fully assembled
Compatible with:Raspberry Pi 5 Raspberry Pi 4
GFX HAT riffs off the previous Display-O-Tron HAT (now discontinued), but gives you the flexibility of individual pixels, letting you display more complex graphics and real typefaces, while retaining the handy capacitive touch buttons for input/navigation.
Features:
Compatible with:
€23.50
Pimoroni Inky pHAT for Raspberry Pi – Black/White
PIM 368
A low-energy, high-falutin, electronic paper (ePaper / eInk / EPD) display for your Pi, in black/white!
Inky pHAT's beautiful, high contrast display is ideal for displaying simple graphics and crisply-rendered text and, because it's like paper, it's readable in bright sunlight. You could use Inky pHAT as a cute little clock, display tweets on it, the weather, news headlines, sports scores, and more. It's also ideal for graphing data from remote sensors, CPU load or temperature, or stock prices.
Features:2.13" EPD display Inky pHAT pinout Compatible with all 40-pin header Raspberry Pi models Python library Comes fully assembled
Compatible with:Raspberry Pi 5 Raspberry Pi 4 Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Header for Pi Zero)
Inky pHAT's beautiful, high contrast display is ideal for displaying simple graphics and crisply-rendered text and, because it's like paper, it's readable in bright sunlight. You could use Inky pHAT as a cute little clock, display tweets on it, the weather, news headlines, sports scores, and more. It's also ideal for graphing data from remote sensors, CPU load or temperature, or stock prices.
Features:
Compatible with:
€29.95
Pimoroni Pirate Audio Headphone Amp for Raspberry Pi
PIM 482
Bring music and sound projects to life with the Pimoroni Pirate Audio Headphone Amp for Raspberry Pi. This compact add-on board combines a high-quality headphone amplifier with a vivid colour display, perfect for creating your own media player or interactive audio project.
The Pirate Audio Headphone Amp from Pimoroni is a clever add-on board designed to deliver excellent sound quality straight from your Raspberry Pi. It includes a built-in 24-bit DAC and 3.5mm stereo headphone output, ensuring crystal-clear audio for your custom music or podcast projects.
The board also features a bright 1.3" IPS colour display and four tactile control buttons, letting you view album artwork, track details, or system info directly from your Pi. It connects neatly via the 40-pin GPIO header, keeping your setup compact and tidy.
Ideal for creating:Raspberry Pi-based music players and jukeboxes Portable headphone amplifiers Interactive sound installations Educational audio projects
Dimensions: Approx. 65mm x 30mm
The Pirate Audio Headphone Amp from Pimoroni is a clever add-on board designed to deliver excellent sound quality straight from your Raspberry Pi. It includes a built-in 24-bit DAC and 3.5mm stereo headphone output, ensuring crystal-clear audio for your custom music or podcast projects.
The board also features a bright 1.3" IPS colour display and four tactile control buttons, letting you view album artwork, track details, or system info directly from your Pi. It connects neatly via the 40-pin GPIO header, keeping your setup compact and tidy.
Ideal for creating:
Dimensions: Approx. 65mm x 30mm
€29.95
Pimoroni Pirate Audio Line-out for Raspberry Pi
PIM 483
Plug Pirate Audio Line-out for Raspberry Pi into your hi-fi amp or powered speakers, then sit back, relax, and soak in the rich, digital audio. It has a high-quality I2S DAC, high-res colour display, and playback control buttons.
This board is perfect for upgrading an existing hi-fi amp and speakers, or a set of powered monitors, with digital audio from local audio files (MP3, FLAC, etc.) or from streaming services. The DAC on Pirate Audio Line-out gives you crisp 24-bit / 192KHz digital audio through its 3.5mm stereo jack.
Pirate Audio is a range of all-in-one audio boards for Raspberry Pi, with high-quality digital audio, beautifully-crisp IPS displays for album art, tactile buttons for playback control, and our custom Pirate Audio software and installer to make setting it all up a breeze.
Features:Line-level digital audio (24-bit / 192KHz) over I2S PCM5100A DAC chip (datasheet) 3.5mm stereo jack 1.3" IPS colour LCD (240x240px) (ST7789 driver) Four tactile buttons Mini HAT-format board Fully-assembled Compatible with all 40-pin header Raspberry Pi models Pirate Audio software Dimensions: 65x30.5x9.5mm
Compatible with:Raspberry Pi 5 Raspberry Pi 4 Raspberry Pi Zero(but needs Male 40-pin 2x20 HAT Header for Pi Zero)
This board is perfect for upgrading an existing hi-fi amp and speakers, or a set of powered monitors, with digital audio from local audio files (MP3, FLAC, etc.) or from streaming services. The DAC on Pirate Audio Line-out gives you crisp 24-bit / 192KHz digital audio through its 3.5mm stereo jack.
Pirate Audio is a range of all-in-one audio boards for Raspberry Pi, with high-quality digital audio, beautifully-crisp IPS displays for album art, tactile buttons for playback control, and our custom Pirate Audio software and installer to make setting it all up a breeze.
Features:
Compatible with:
€29.95
Raspberry Pi 32GB Micro SD Card A2 Class Pre-Programmed (In Case)
RP SC1660LM
Optimise data transfer speeds on your Raspberry Pi computer with an official Raspberry Pi SD Card. Rigorously tested to ensure optimal performance on Raspberry Pi computers, these Class A2 microSD cards help ensure you get the smoothest user experience from your device.
Documents:Raspberry Pi SD Cards Offical Product Brief
Documents:
€8.95
Payment options
